Case 3

Standards

[su_tabs]

[su_tab title=”BS”]

Screeding

BS 8000-0:2014 Workmanship on construction sites. Introduction and general principles

Tilings

BS 6319-12:1992 Testing of resin and polymer/cement compositions for use in construction. Methods for measurement of unrestrained linear shrinkage and coefficient of thermal expansion

BS 5385-5:2009 Wall and floor tiling. Design and installation of terrazzo, natural stone and agglomerated stone tile and slab flooring. Code of practice

BS 5385-1:2009 Wall and floor tiling. Design and installation of ceramic, natural stone and mosaic wall tiling in normal internal conditions. Code of practice

BS 8221-1:2012 Code of practice for cleaning and surface repair of buildings. Cleaning of natural stone, brick, terracotta and concrete

BS 8221-2:2000 Code of practice for cleaning and surface repair of buildings. Surface repair of natural stones, brick and terracotta

BS EN 14157:2004 Natural stones. Determination of abrasion resistance

BS EN 12004:2007+A1:2012 Adhesives for tiles. Requirements, evaluation of conformity, classification and designation

[/su_tab]

[su_tab title=”ASTM”]

Cement Mortar and Grout

ASTM C305 – 14 Standard Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency

ASTM C778 – 13 Standard Specification for Standard Sand

ASTM C109 / C109M – 16a Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)

ASTM C348 – 14 Standard Test Method for Flexural Strength of Hydraulic-Cement Mortars

ASTM C349 – 14 Standard Test Method for Compressive Strength of Hydraulic-Cement Mortars (Using Portions of Prisms Broken in Flexure)

ASTM C150-07 Standard Specification for Portland Cement

ASTM C87 / C87M – 10 Standard Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar

ASTM C125-15b Standard Terminology Relating to Concrete and Concrete Aggregates

ASTM C1038 / C1038M – 14b Standard Test Method for Expansion of Hydraulic Cement Mortar Bars Stored in Water

ASTM C494 / C494M – 15a Standard Specification for Chemical Admixtures for Concrete

ASTM C115 / C115M – 10e1 Standard Test Method for Fineness of Portland Cement by the Turbidimeter

ASTM C490/C490M-11e1 Standard Practice for Use of Apparatus for the Determination of Length Change of Hardened Cement Paste, Mortar, and Concrete

ASTM C33 / C33M – 16 Standard Specification for Concrete Aggregates

ASTM C295 / C295M – 12 Standard Guide for Petrographic Examination of Aggregates for Concrete

ASTM C452 – 15 Standard Test Method for Potential Expansion of Portland-Cement Mortars Exposed to Sulfate

Tilings

ASTM C503 / C503M – 15 Standard Specification for Marble Dimension Stone

ASTM C568 / C568M – 15 Standard Specification for Limestone Dimension Stone

ASTM F963 – 11 Standard Consumer Safety Specification for Toy Safety

ASTM E1857 – 97(2013)e1 Standard Guide for Selection of Cleaning Techniques for Masonry, Concrete, and Stucco Surfaces

ASTM D5107 – 03(2013) Standard Practice for Preparatory Surface Cleaning of Architectural Sandstone

[/su_tab]

[su_tab title=”AS”]

Plaster and Screed

AS CA27-1959 Code of recommended practice for internal plastering on solid backgroundsAS CA27-1959 Code of recommended practice for internal plastering on solid backgrounds

Cement Mortar and Grout

AS 1478.2-2005 Chemical admixtures for concrete, mortar and grout – Methods of sampling and testing admixtures for concrete, mortar and grout

AS 1012.18-1996 (R2014) Methods of testing concrete – Determination of setting time of fresh concrete, mortar and grout by penetration resistance AS 1478.1-2000 Chemical admixtures for concrete, mortar and grout – Admixtures for concrete

AS 2350.12-2006 Methods of testing portland, blended and masonry cements – Preparation of a standard mortar and moulding of specimens

AS 2350.13-2006 Methods of testing portland, blended and masonry cements – Determination of drying shrinkage of cement mortars

AS 2350.14-2006 Methods of testing portland, blended and masonry cements – Length change of cement mortars exposed to sulfate solution

[/su_tab]

[su_tab title=”SS”]

Rendering

SS 397 – 7 : 1997 Methods of testing cement – Method of taking and preparing samples of cement (Withdrawn 24 Jun 2011) (Users can refer to parts of BS EN 196)

SS EN 197 series – Cement

Tilings

SS 483 : 2000 Ceramic tiles – Definitions, classification, characteristics and marking (Withdrawn – 12 Sep 2007) (Users can refer to ISO 13006 and ISO 10545)

SS 509 – 1 : 2015 Code of practice for cleaning and surface repair of buildings – Part 1 : Cleaning of natural stone, brick, terracotta, concrete and rendered finishes

CP 68 : 1997 Code of practice for ceramic wall and floor tiling

[/su_tab]

[su_tab title=”ISO”]

Cement Mortar and Grouting

ISO 29581-1:2009  Cement — Test methods — Part 1: Analysis by wet chemistry

ISO 863:2008 Cement — Test methods — Pozzolanicity test for pozzolanic cements

Tilings

ISO 603-10:1999 Bonded abrasive products — Dimensions — Part 10: Stones for honing and superfinishings

ISO 8512-2:1990 Surface plates — Part 2: Granite

[/su_tab]

[/su_tabs]